Jump to content
  • 0
Sign in to follow this  
vykimo

GHOST textures or BLANK ground....

Question

Hello,

I've one question for the extremely-friendly browedit's mappers :

216153screenHercules000.jpg

 

How can I remove this ghost textures? AS you can see on the screenshot, it happend ONLY on the bottom of the screen (and rarely on the top) and partially.

BUT, I already tested following solutions :

  1.  Changing with an hex-editor the version of the quadtree to 0x109 : the result is worse
  2. I tryed to raise the height of the ground of the fountain in the center ( it's a hole ) : no effect
  3. I tryed to bring closer the models to the ground (I raised the low-lying models and dropped the high-lying models) : no effect too
  4. I tryed too to raise the height of water... no effect
  5. And finally, I tried to save with Brow v.620 : There is no more this problem of ghost texture on the bottom But There are too many ghost models around the map.

 

That why I prefer BrowEdit 586 to save.

 

Does anyone have an answer? :(

 

 

EDIT/ The most curious thing, is when I raise the water height, WE CAN SEE that only a small part is not loaded :

627591screenHercules000.jpg

 

 

Wtfgravity?

Edited by vykimo

Share this post


Link to post
Share on other sites

5 answers to this question

Recommended Posts

  • 0

First of all, rev.620 of Browedit is not good for final saving the map. Use rev. 586 for that. What I do to get rid of those not loading parts is open the map in rev. 586 of BrowEdit, insert to full, generate -> quadtree, and then save the map. See if that helps.

Share this post


Link to post
Share on other sites
  • 0

First of all, thanks for you answer.

 

But, I don't know if i'm clear but I said that :

And finally, I tried to save with Brow v.620 : There is no more this
problem of ghost texture on the bottom But There are too many ghost
models around the map.

I always save with 586 with generating quadtree before, but I only tried to save with the last version to see what happend.... :/

 

Any another reply?

Share this post


Link to post
Share on other sites
  • 0

Oh, sorry.

 

Hmm. Since you tried with quadtree generating, I sometimes saw an advice to raise the ground above 0 height level. Set your water level to 0 and check if any parts of your map are under the water. If so, you'd need to raise it so it doesn't fall under the 0 height mark. (You mentioned raising parts, and changing height of objects, but the point here is everything being above 0 height)

Share this post


Link to post
Share on other sites
  • 0

Excellent answer, i'm not sure about it, but i need to raise all the map to have all my models and ground above 0 height mark? When I set the water level to 0, i've no texture under the water but some object are a bit submerged.

 

EDIT :

IT's way better !! I upped a bit my models/ground/gat and the problem reduced a bit :

before:

947307screenHercules018.jpg

 

after:

613384screenHercules017.jpg

 

EDIT 2 : Finally when raising higher than previously, the blank textures totally desepear. Ty a lot Garr, it's a big step for human ragnarok mapping's community.

Edited by vykimo

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Answer this question...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.